Results 1 to 14 of 14
Thread: Yonex VT80 Grommet Strip
10-09-2011, 11:48 PM #1
Yonex VT80 Grommet Strip
Interesting how most other rackets have gotten them and the Nanorays have already come out before yonex has these available. So just wondering if anyone has tried the AT900P Grommet Strips on the VT80 or should I order the ones for the Arc10. Seems like yonex would rather have us buying new than to maintain!
10-10-2011, 10:19 AM #2
I get a friend who uses it. It works for him!
Optiblue liked this post
10-10-2011, 10:22 AM #3
Sup pete! So for sure it's the AT900P and not the AT900T correct? I can't believe there's a slight variation between the two! I'll order a set then
10-10-2011, 11:54 AM #4
10-10-2011, 12:46 PM #5
Cool thanks! Those strips are a god send
Blitzzards liked this post
10-11-2011, 02:15 AM #6
Apologies for crashing this thread, but this seemed the best place to ask a quick (relevant) question.
I was wondering if anyone knows if any of these grommet strips fit a VT70?
Is anyone currently using them with a Voltric 70? - Which ones?
10-11-2011, 10:03 AM #7
anthemtwins liked this post
10-11-2011, 10:38 AM #8
Where can you order these grommet strips?
Is it easy to install or better to pay full price from the stringer to replace when necessary?
10-11-2011, 10:48 AM #9
Funny, I tried the 6X strip of AT900P (cat#AC416L-4)
and the 2X strip (cat# AC416W-2) and it didn't fit my Voltric 80.
The experiment failed, So what you guys say above is not a true fit.
(It only works if you cut the grommets to fit)
Last edited by Badmintan; 10-11-2011 at 11:00 AM.
10-11-2011, 12:19 PM #10
10-11-2011, 02:21 PM #11
10-12-2011, 03:53 AM #12
In my experimental findings, the AT900P 6x grommet was a tad too long to fit in the VT80. I have to cut the grommet in 2 to fit in. In addition, the 2X grommet was too short. Please refute my claims with pictures.
I'll perhaps post a picture of the VT80 and AT900P side by side and measure the holes distance with a measuring tape, to be more convincing.
Last edited by Badmintan; 10-12-2011 at 03:56 AM.
10-12-2011, 06:35 AM #13
I have used the continuous grommets in my VT80
My favorite store sell the grommets and it fits with a little bulge in 1 grommet hole.
I don't know the code number of the grommets
Visually in the middle of the long grommet (there are 6 holes)
the space between grommet's hole 3 & 4 is longer than the rest of grommet
It's a good investment to protect your racket from frame sinking and extend the durability even better
02-03-2013, 12:01 AM #14
By Blitzzards in forum Badminton Rackets / EquipmentReplies: 117: 05-15-2012, 11:58 AM
By Dave1011 in forum Badminton Rackets / EquipmentReplies: 7: 04-17-2012, 03:20 PM
By CanucksDynasty in forum Buy & SellReplies: 3: 03-23-2012, 03:01 PM
By Deathsticks in forum Badminton Rackets / EquipmentReplies: 2: 04-13-2009, 01:14 AM
By macchan in forum Badminton Rackets / EquipmentReplies: 4: 06-19-2008, 07:09 AM