VIDEO: weaving and tension cross w/ local pre-weave

Discussion in 'Badminton Stringing Techniques & Tools' started by kwun, Mar 18, 2012.

  1. kwun

    kwun Administrator

    Joined:
    Apr 24, 2002
    Messages:
    41,041
    Likes Received:
    2,065
    Occupation:
    BC Janitor
    Location:
    Santa Clara, CA, USA
    Here is the video on how to weave and tension cross strings with local pre-weave.

    A few things that i tried to cover in the video.

    - weaving the cross, over-and-under (basic but i think it should be talked about to be complete)
    - mentioned soft and hard weave
    - ok to weave perpendicular with soft
    - easier weave diagonally with hard weave
    - holding onto the string end
    - tensioning
    - straightening cross when tension
    - massage cross when tension to relieve friction

    it seems that i talked a bit too much as the length of the video has ballooned to 9 mins this time. which is not that convincing if that's what it takes to do 4 crosses.

    [video=youtube;VnbFq0lge6A]http://www.youtube.com/watch?v=VnbFq0lge6A[/video]

    as usual, any comments are welcomed.
     
  2. KingO

    KingO Regular Member

    Joined:
    Oct 11, 2006
    Messages:
    64
    Likes Received:
    2
    Occupation:
    RN
    Location:
    SoCal
    I string my crosses 1 ahead to take advantage of the soft weave technique also. After I weave the cross, I usually just leave the approx 6 inches of string sticking out (keeps me from holding on to the string or looking for the string end on the floor) and not pull the rest of the string across. I pull the rest of the string before I do my next soft weave using the diagonal method of pulling the string across you showed in your video.
     
  3. Loafers

    Loafers Regular Member

    Joined:
    Aug 18, 2008
    Messages:
    127
    Likes Received:
    2
    Occupation:
    Loafer
    Location:
    USA
    [​IMG]

    you should make a sticky thread for all your videos :)
     
  4. Mark A

    Mark A Regular Member

    Joined:
    Sep 2, 2005
    Messages:
    7,170
    Likes Received:
    695
    Location:
    St Helens, UK
    Any particular reason for weaving four ahead? It's an extra hard weave, after all... I've seen Alan K do this as well, though, so you're in good company:). I suppose it would get a couple of feet of string off the floor.

    O/T - have you tried stringing the SW35 with the extra cross at the bottom? I always did:D.
     
  5. _Rav_

    _Rav_ Regular Member

    Joined:
    Oct 26, 2010
    Messages:
    209
    Likes Received:
    10
    Occupation:
    Gofer
    Location:
    UK
    I tend to preweave the last 6-8 if i do bottom up, as the deacreasing space at the top, especially with a load spreader makes it hard work. It's not so much of a problem top down though.
     
  6. kwun

    kwun Administrator

    Joined:
    Apr 24, 2002
    Messages:
    41,041
    Likes Received:
    2,065
    Occupation:
    BC Janitor
    Location:
    Santa Clara, CA, USA
    i find the fewer tool and process change make it whole process smoother and faster.

    i mainly do local pre-weave now. i tried to change to weave one-ahead for a few dozen rackets but never able to adjust to it.

    from play testing, the resultant stringjobs feels the same.

    i do suggest everyone try both methods and experiment to see how they like the process as well as the results. and pick the one that you feel better with.
     
  7. kwun

    kwun Administrator

    Joined:
    Apr 24, 2002
    Messages:
    41,041
    Likes Received:
    2,065
    Occupation:
    BC Janitor
    Location:
    Santa Clara, CA, USA
    for bottoms up, i go back to one-ahead to minimize twisting at the shared hole and for non-shared hole that has string rubbing.
     
  8. Mark A

    Mark A Regular Member

    Joined:
    Sep 2, 2005
    Messages:
    7,170
    Likes Received:
    695
    Location:
    St Helens, UK
    I do top-down and pre-weave the top five or six crosses before all the mains are in (to make the shared holes easier). This certainly causes twisting if I'm not careful, though.
     
  9. sr20det

    sr20det Regular Member

    Joined:
    Jun 19, 2016
    Messages:
    31
    Likes Received:
    10
    Location:
    malaysia
    Has anyone pre-weave a racket directly from a 200m reel. As you know, the objective is to optimise string usage. I normally throw away up to 1.6m of string on a standard 10m pack. I was told I could get some mileage out of the 200m reel up to 22 rackets. Any one can share their experience?
     
  10. DuckFeet

    DuckFeet Regular Member

    Joined:
    Feb 22, 2012
    Messages:
    2,032
    Likes Received:
    320
    Occupation:
    Computer rebooter
    Location:
    Swindon
    Not really a question on preweaving, I avoid it due to string kinking, but yes I get 21 from a zymax fire and 22 from li ning. I one piece, mostly low/mid tension.
     
  11. xZhongCheng

    xZhongCheng Regular Member

    Joined:
    Jan 25, 2009
    Messages:
    497
    Likes Received:
    167
    Occupation:
    Systems Analyst
    Location:
    CA
    I have gotten 23 rackets done with 1 roll many times.

    I find 5 arms spans is perfect length for the rackets, doing the haribito one piece =)
     
  12. sr20det

    sr20det Regular Member

    Joined:
    Jun 19, 2016
    Messages:
    31
    Likes Received:
    10
    Location:
    malaysia

Share This Page