Results 1 to 17 of 20
03-26-2012, 05:24 PM #1
Is this crack due to a stringing flaw?
My Nanospeed 800 got restrung with BG66 Ultimax @ 24lb and I noticed that it had a hairline crack.
The problem is that I wasn't sure whether the crack was there before the restringing. I continued playing with the racket for a few more hours and the crack opened up. It's now basically unusable
I was told by the stringer (who also owns the Badminton club I go to) that the crack was due to a clash, which seems legitimate because I remember clashing my racket LOADS of times during it's 2.5 year period. This racket was bought when I was still a beginner and progressed me up to intermediate level, so it is likely that the amount of clashes may have slowly worn it down.
The purpose of this thread though, is that I want to know whether this crack was made by a clash or if it was a stringing flaw. I will appreciate quick responses because I want to make my mind up before Saturday as my shiny Nanospeed 9900 should be coming tomorrow
If it was a stringing flaw, I'll check out another stringer. But if it wasn't, then I would prefer to give the NS9900 to the owner over the weekend to restring the BG66U so that it will be ready next session.
Here are the pictures:
Thanks in advance.
03-26-2012, 05:32 PM #2
hard to say. a few points.
1. did you noticed the crack before you give it to the stringer?
2. the stringer is supposed to look for evidence of damage before stringing the racket. even though at times the damage may not be visible.
3. you said there are numerous clashes. but is there a noticible chip near the crack?
4. usually when a racket is damaged during the process, the crack and crumbling happens pretty quickly and destructively.
looks to me a 50/50 case.
03-26-2012, 05:37 PM #3
1. No, simply because I didn't have a good look at minor details before it was strung.
2. I admit, if there was a crack, it would have been literally invisible. When I received my racket back, I wasn't even sure if it was a crack; I thought it may have been a paint chip.
3. My racket is littered with chips lol. It was a mid-range racket made in Taiwan, so it was kinda expected, especially after being used for a good 2.5 years. But yes, the crack was 'inside' a paint chip when I noticed it first.
4. After I saw the crack, it opened up pretty quickly. It must have taken ~7 hours to get from a hairline to the ones above.
Thanks for your response.
I hope this helps.
03-26-2012, 05:39 PM #4
2.5 years with LOADS of clashes? I think you're lucky you got 2.5 years out of it.
Is this the first time you've used this stringer or has he always been stringing your racket? If it's the latter...chances are your racket was ready to die after so many clashes.
03-26-2012, 05:42 PM #5
Probably about 6-7 clashes, but from beginner - lower intermediate players, so it's possible that it may not have contributed too much, but who knows.
Regarding the stringer, it was my first time restringing with him. He seemed pretty experienced but I'm no expert at stringing, so I don't know.
03-26-2012, 05:49 PM #6
kwun liked this post
03-26-2012, 05:52 PM #7
03-26-2012, 06:06 PM #8
I like higher tension. So the guy I go to uses a 6 point ECP machine (Yonex ESPro?). So I'm confident my racket isn't warped and has the correct tension as well. And if my racket ever breaks...it's probably due to my crappy play than his string job.
03-26-2012, 06:11 PM #9
Here's the alternative stringer I'm thinking of. It'll take ~1 hour to reach there, but by first impressions, do they look good and professional enough? (bare in mind they only have one store)
03-26-2012, 06:21 PM #10
You should ask your friends and other badminton enthusiasts in your area for stringing recommendation. There might even be a stringer in your area that frequents these forums.
And the website link doesn't really tell me anything about stringing services. The store I go to has a really bad outdated website and is a small hole in the wall crammed with badminton/tennis stuff. So you can't really judge it by it's appearances.
03-27-2012, 07:45 AM #11
I was just wondering, could the crack be because of 24x24 tension?
I was following this thread and noticed how no extra cross tensions could deform a frame.
Could this be it? And in future, shall I string to 24x26?
Lastly, as my NS9900 has a max tension recommendation of 24lb, will the 24x26 be voiding the warranty?
03-27-2012, 11:39 AM #12
nope. 24x24 is fine.
03-27-2012, 12:14 PM #13
03-27-2012, 02:05 PM #14
03-27-2012, 02:07 PM #15
The maximum is 24lb...
03-29-2012, 04:31 PM #16
03-29-2012, 04:33 PM #17
By SirEdward in forum Badminton Rackets / EquipmentReplies: 7: 03-31-2009, 12:33 AM
By richsaccount in forum Badminton Rackets / EquipmentReplies: 12: 05-12-2008, 10:09 PM
By NoIso4Me in forum Badminton Stringing Techniques & ToolsReplies: 29: 06-08-2005, 02:19 PM
By Gilly23 in forum Badminton Stringing Techniques & ToolsReplies: 1: 06-06-2005, 02:43 PM
By Jason in forum Badminton Rackets / EquipmentReplies: 13: 12-23-2001, 03:25 AM