Results 154 to 170 of 235
04-09-2010, 01:25 PM #154
04-09-2010, 01:36 PM #155
it is on the yonex pack. can you give me detail procedure on stringing 1 piece.
and for 2 pieces method how much length should i allow on the left side of the racket.
thanks for your reply.
04-09-2010, 01:45 PM #156
I will do my best to answer your question even I am not feeling too good right now.
1) For 1 piece, please measure 2.75~2.9 meater from one end. That should be the length for the short side.
2) for 2 pieces, please measure 5.5~5.75 meter from one end. Cut. The long one is for your main and short is for you cross...
04-09-2010, 02:09 PM #157
for 1 piece method, should i follow the procedures of yonex. or will these be a contunous stringing without cutting the strings.
04-09-2010, 02:25 PM #158
04-09-2010, 03:08 PM #159
can i just wait till you feel fine "Silentheart" i felt dizzy also doing this stringing.... thanks
04-11-2010, 11:33 AM #160
is there any advantage between 1 piece method and 2 piece method.
04-11-2010, 11:57 AM #161
For a good stringer, it should not make much of a difference playability wise. However, if the user is sensitive to string tension changes, I'd imagine two piece would provide a better feel as it does to me. Not to mention that 1 piece exerts more strain on the racket than 2 piece
05-10-2010, 01:00 AM #162
what would you recommend as the max tension for this machine? i've strung it many times at 25x28lbs and i love that tension, but recently i've broken a racket at that tension and now i've lost quite a bit of my confidence. should i just stick with 24lbs max? the racket wasn't a lower end racket at all and i assumed it could take the strain as even my wilson dynapower 9500 could take it.
05-10-2010, 02:20 AM #163
I didn't know you used an M140???
Honestly, two point, even with the load spreaders built in on this machine, I wouldn't pull higher than 26 or 27 on it.
So on a 25x28 job, I'd have to manually prestretch the string to 31lbs (using a doorknob, Yonex flying clamps, and a tension calibrator) and even then, depends on string used. My
final opinion is 25/28 is really the very upper limit. I've done 30 on it (28.5/31.5) without problems but I took my dear sweet time really cranking all the bolts to make sure it was all secured properly.
05-10-2010, 08:36 AM #164
2) Most of YY racquet are fine up to 27lb on M140. Make sure you use 2 piece and throat up currently recommended by YY.
05-10-2010, 03:50 PM #165
alright, thanks a lot you guys. hm, i made sure to tighten all the bolts and align the racket up with the supports perfectly, not even 1mm of space between the racket and the support. i'll try going throat up next time, thanks a lot.
07-10-2010, 06:02 PM #166
Just finished stringing my Armortec 900 Technique @ 30x32 with this machine that I received yesterday.
12-26-2010, 12:13 AM #167
hi, there new in the forum and I just bought a M140 for stringing my badminton rackets, I notice there is a conversion chart for tennis and badminton on the machine, I did not find it to be mentioned anywhere, so just to make sure, you have to use the chart lets say 60lbs on the scale to be equal to 20 for badminton? Also in the instruction manual, the tension for the rackets seems to be wrong for the yonex rackets.. Thx in advance for the help.
12-26-2010, 12:26 AM #168
it should come with 2 weights bigger one for tennis a smaller one for badminton. If you dont have the badminton(smaller) one then you can use the tennis one but you may be limited to higher tension. lb for lb it should be the same regardless of racket type. make sure you fully understand how to use the klippermate by reading thoroughly through this thread (mainly securing the 2 post when stringing) good luck
12-26-2010, 11:41 PM #169
I ordered the badminton set therefore it only came with the small weight, the clamp i had is written klipperusa.com on it, anyone know if this is a good clamp or do I need to buy some new ones?
02-27-2011, 06:44 PM #170
Dear Master Silentheart,
You are the best teacher! Thanks for your help!
By Shoutsu in forum Badminton Stringing Techniques & ToolsReplies: 7: 01-04-2013, 12:38 PM
By Shoutsu in forum Badminton Stringing Techniques & ToolsReplies: 2: 05-05-2011, 09:14 PM
By hasan in forum Buy & Sell - Read the rules sticky before you postReplies: 3: 05-19-2009, 06:19 PM
By jif226 in forum Badminton Stringing Techniques & ToolsReplies: 14: 03-12-2007, 01:26 PM
By FAST! in forum Badminton Stringing Techniques & ToolsReplies: 4: 10-15-2005, 01:22 PM