User Tag List

Page 10 of 14 FirstFirst 1 2 3 4 5 6 7 8 9 10 11 12 13 14 LastLast
Results 154 to 170 of 238
  1. #154
    Regular Member
    Join Date
    Oct 2004
    Location
    USA
    Posts
    4,657
    Mentioned
    4 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by fandulan View Post
    i have a 10 meter atring. how much length do i need to place on the left and right of the racket.
    1) is this 10 meter string from a pack or you measured it?
    2) Are you using 1 piece or 2 pieces method?
    3) Don't go out drinking till 8:00pm and go back to office and work till 10:30 and get back home 2:00 am and return back to work 8:00am again. It is just ....

  2. #155
    Regular Member
    Join Date
    Jan 2010
    Location
    saudi arabia
    Posts
    17
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    it is on the yonex pack. can you give me detail procedure on stringing 1 piece.
    and for 2 pieces method how much length should i allow on the left side of the racket.
    thanks for your reply.

  3. #156
    Regular Member
    Join Date
    Oct 2004
    Location
    USA
    Posts
    4,657
    Mentioned
    4 Post(s)
    Tagged
    0 Thread(s)

    Default

    I will do my best to answer your question even I am not feeling too good right now.
    1) For 1 piece, please measure 2.75~2.9 meater from one end. That should be the length for the short side.
    2) for 2 pieces, please measure 5.5~5.75 meter from one end. Cut. The long one is for your main and short is for you cross...

  4. #157
    Regular Member
    Join Date
    Jan 2010
    Location
    saudi arabia
    Posts
    17
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    for 1 piece method, should i follow the procedures of yonex. or will these be a contunous stringing without cutting the strings.

  5. #158
    Regular Member
    Join Date
    Oct 2004
    Location
    USA
    Posts
    4,657
    Mentioned
    4 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by fandulan View Post
    for 1 piece method, should i follow the procedures of yonex. or will these be a contunous stringing without cutting the strings.
    for 1 piece, please tie off at B8 on short side only. use the rest of the long string, go through B9 and start the cross from there.

  6. #159
    Regular Member
    Join Date
    Jan 2010
    Location
    saudi arabia
    Posts
    17
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    can i just wait till you feel fine "Silentheart" i felt dizzy also doing this stringing.... thanks

  7. #160
    Regular Member
    Join Date
    Jan 2010
    Location
    saudi arabia
    Posts
    17
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    is there any advantage between 1 piece method and 2 piece method.

  8. #161
    Regular Member
    Join Date
    Mar 2009
    Location
    Davis, CA
    Posts
    1,218
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    For a good stringer, it should not make much of a difference playability wise. However, if the user is sensitive to string tension changes, I'd imagine two piece would provide a better feel as it does to me. Not to mention that 1 piece exerts more strain on the racket than 2 piece

  9. #162
    Regular Member
    Join Date
    Jul 2008
    Location
    San Jose, Ca
    Posts
    195
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default

    what would you recommend as the max tension for this machine? i've strung it many times at 25x28lbs and i love that tension, but recently i've broken a racket at that tension and now i've lost quite a bit of my confidence. should i just stick with 24lbs max? the racket wasn't a lower end racket at all and i assumed it could take the strain as even my wilson dynapower 9500 could take it.

  10. #163
    Regular Member
    Join Date
    Mar 2009
    Location
    Davis, CA
    Posts
    1,218
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    I didn't know you used an M140???

    Honestly, two point, even with the load spreaders built in on this machine, I wouldn't pull higher than 26 or 27 on it.

    So on a 25x28 job, I'd have to manually prestretch the string to 31lbs (using a doorknob, Yonex flying clamps, and a tension calibrator) and even then, depends on string used. My
    final opinion is 25/28 is really the very upper limit. I've done 30 on it (28.5/31.5) without problems but I took my dear sweet time really cranking all the bolts to make sure it was all secured properly.

  11. #164
    Regular Member
    Join Date
    Oct 2004
    Location
    USA
    Posts
    4,657
    Mentioned
    4 Post(s)
    Tagged
    0 Thread(s)

    Default

    Quote Originally Posted by bobbinbette View Post
    what would you recommend as the max tension for this machine? i've strung it many times at 25x28lbs and i love that tension, but recently i've broken a racket at that tension and now i've lost quite a bit of my confidence. should i just stick with 24lbs max? the racket wasn't a lower end racket at all and i assumed it could take the strain as even my wilson dynapower 9500 could take it.
    1) Special support. I have a special support I design and made myself for Yonex racquet with recommended tension less than 25lb. For racquet higher than 28lb, I will use the support. For ARC8dx. i will be fine to go up to 29lb without side support.
    2) Most of YY racquet are fine up to 27lb on M140. Make sure you use 2 piece and throat up currently recommended by YY.

  12. #165
    Regular Member
    Join Date
    Jul 2008
    Location
    San Jose, Ca
    Posts
    195
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default

    alright, thanks a lot you guys. hm, i made sure to tighten all the bolts and align the racket up with the supports perfectly, not even 1mm of space between the racket and the support. i'll try going throat up next time, thanks a lot.

  13. #166
    Regular Member
    Join Date
    Aug 2008
    Location
    Trinidad
    Posts
    140
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Just finished stringing my Armortec 900 Technique @ 30x32 with this machine that I received yesterday.

  14. #167
    Regular Member
    Join Date
    Jul 2010
    Location
    Montreal
    Posts
    17
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    hi, there new in the forum and I just bought a M140 for stringing my badminton rackets, I notice there is a conversion chart for tennis and badminton on the machine, I did not find it to be mentioned anywhere, so just to make sure, you have to use the chart lets say 60lbs on the scale to be equal to 20 for badminton? Also in the instruction manual, the tension for the rackets seems to be wrong for the yonex rackets.. Thx in advance for the help.

  15. #168
    Regular Member
    Join Date
    Apr 2006
    Location
    vancouver
    Posts
    625
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    ^
    it should come with 2 weights bigger one for tennis a smaller one for badminton. If you dont have the badminton(smaller) one then you can use the tennis one but you may be limited to higher tension. lb for lb it should be the same regardless of racket type. make sure you fully understand how to use the klippermate by reading thoroughly through this thread (mainly securing the 2 post when stringing) good luck

  16. #169
    Regular Member
    Join Date
    Jul 2010
    Location
    Montreal
    Posts
    17
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    I ordered the badminton set therefore it only came with the small weight, the clamp i had is written klipperusa.com on it, anyone know if this is a good clamp or do I need to buy some new ones?

  17. #170
    New Member
    Join Date
    Feb 2011
    Location
    USA
    Posts
    1
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Dear Master Silentheart,

    You are the best teacher! Thanks for your help!

Page 10 of 14 FirstFirst 1 2 3 4 5 6 7 8 9 10 11 12 13 14 LastLast

Similar Threads

  1. Klipper M140 Scale, accurate?
    By Shoutsu in forum Badminton Stringing Techniques & Tools
    Replies: 7
    : 01-04-2013, 12:38 PM
  2. Klipper M140 Specifics
    By Shoutsu in forum Badminton Stringing Techniques & Tools
    Replies: 2
    : 05-05-2011, 09:14 PM
  3. FS: Klipper M140 stringning machine for sale
    By hasan in forum Buy & Sell - Read the rules sticky before you post
    Replies: 3
    : 05-19-2009, 06:19 PM
  4. Klipper M140 Clamp problem
    By jif226 in forum Badminton Stringing Techniques & Tools
    Replies: 14
    : 03-12-2007, 01:26 PM
  5. Klipper Stringing guide
    By FAST! in forum Badminton Stringing Techniques & Tools
    Replies: 4
    : 10-15-2005, 01:22 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •