WTB: 6-point drop weight stringing machine

Discussion in 'Buy & Sell - Read the rules sticky before you post' started by mnanchala, Sep 11, 2008.

  1. mnanchala

    mnanchala Regular Member

    Joined:
    Nov 20, 2002
    Messages:
    166
    Likes Received:
    0
    Occupation:
    Engineer
    Location:
    Dallas, TX, USA
    I am looking for a drop weight stringing machine. I have never strung before so it will be my first one. But I intend to keep this machine for long.

    I don't need fancy stuff.

    * Need 6 point support because I string starting at 23x25 lbs. I may try higher in the near future.

    * Need drop weight because I believe they are the most consistent and need less calibration over time.

    My budget is $200 US. But if there is a good one I might spend more. I know it is not much, but I am not necessarily looking for a brand new machine. Something that is NOT broken and gets the job done will do. I don't care if it has a few scratches here and there.

    Show me what you got. :)
     
  2. Pete LSD

    Pete LSD Regular Member

    Joined:
    Apr 25, 2002
    Messages:
    6,297
    Likes Received:
    13
    Occupation:
    Soul Searching
    Location:
    Canada
  3. Pete LSD

    Pete LSD Regular Member

    Joined:
    Apr 25, 2002
    Messages:
    6,297
    Likes Received:
    13
    Occupation:
    Soul Searching
    Location:
    Canada
    I haven't tried Mutual Power yet.

    Hercules 690 has single hand operation. Again, ask for badminton fixed clamps and better fixed clamp system (the cone and base) like the Atlas 9600 (if it fits on the Hercules 690).
    http://www.mutualpower.net/sm.htm
     
  4. Pete LSD

    Pete LSD Regular Member

    Joined:
    Apr 25, 2002
    Messages:
    6,297
    Likes Received:
    13
    Occupation:
    Soul Searching
    Location:
    Canada
  5. mnanchala

    mnanchala Regular Member

    Joined:
    Nov 20, 2002
    Messages:
    166
    Likes Received:
    0
    Occupation:
    Engineer
    Location:
    Dallas, TX, USA
    Thank you for all the advice Pete. The Silent Partner Hip Hop is definitely a candidate. The MP Hercules 690 looks very similar too.

    But like I mentioned, my budget is a little low right now ($200). Maybe $300 max. But I do have to spend some on flying clamps, fixed clamps and such..
     
  6. Pete LSD

    Pete LSD Regular Member

    Joined:
    Apr 25, 2002
    Messages:
    6,297
    Likes Received:
    13
    Occupation:
    Soul Searching
    Location:
    Canada
    Here is the kicker. You can saw off the ends of the turntable (search for DinkALot's machine modification) and move the tensioner much closer (ask Kwun for photos). Bear in mind that moving the tensioner closer to the turntable requires you to keep the angle between the edge of the support column and the edge of the rotary tensioner constant. Ok, it calls for a new thread in the stringing forum. Will post more tonight.
     
  7. mnanchala

    mnanchala Regular Member

    Joined:
    Nov 20, 2002
    Messages:
    166
    Likes Received:
    0
    Occupation:
    Engineer
    Location:
    Dallas, TX, USA
    ^bump^

    15 characters
     
  8. mnanchala

    mnanchala Regular Member

    Joined:
    Nov 20, 2002
    Messages:
    166
    Likes Received:
    0
    Occupation:
    Engineer
    Location:
    Dallas, TX, USA
    ^bump^

    15 characters
     
  9. mnanchala

    mnanchala Regular Member

    Joined:
    Nov 20, 2002
    Messages:
    166
    Likes Received:
    0
    Occupation:
    Engineer
    Location:
    Dallas, TX, USA
    ^ still looking ^
     

Share This Page