Results 137 to 153 of 240
Thread: CW and TH Grip
09-01-2010, 03:41 PM #137
So I tried it
That was for sure thinner than original + Ac102, and that was easier to hold the racquet
Unfortunately the feeling was veryyyy hard...
Perhaps putting any tape or thin overgrip under the AC102 will make it more comfortable
09-10-2010, 04:19 AM #138
Is LCW using 2 roll of grip to grip his racket? I tried 1 roll of grip on my racket today but found it not very thick though..
09-10-2010, 03:44 PM #139
On the video Ants shown only one roll
I also faced the prob (post #137)..
I think you could put a tape on the wood
09-10-2010, 04:06 PM #140
I am now using a hybrid grip, that I have had the wonderful pleasure of inventing
It is a combo of the LD grip and LCW grip, basically you start the way that ants has showed you in the video, and keep twisting, until you get about 2/3 up, where you stop, a good thing about this, is that out of the standard 3 supergraps per pack, you can make 1 grip into between two and three depending on how tight you wrap, how short you finish gripping, and if you are wrapping on top of a original grip or not.
Btw I am using Yellow AC102EX
Last edited by LD rules!; 09-10-2010 at 04:08 PM.
09-10-2010, 04:20 PM #141
Directly on the wood ?
That's not a good method for me as I play doubles
09-10-2010, 04:22 PM #142
09-10-2010, 04:32 PM #143
Isn't the point of the method to end up with the sticky part on top? If you're gonna cut it off, might as well do it the regular way
(saves you a few more inches as well by skipping the starting method )
Last edited by demolidor; 09-10-2010 at 04:41 PM.
09-10-2010, 04:42 PM #144
So does LCW also rule ?
Since you use his gripping style...
Last edited by Thom_bad; 09-10-2010 at 04:45 PM.
09-10-2010, 04:51 PM #145
09-10-2010, 05:00 PM #146
What grip size do you use for your LD-LCW grip ?
Dunno how it was for Demolidor, but with my YY G4 I even can't put the grip untill the high of the cone..with a 1/2 overlap !!
09-10-2010, 05:16 PM #147
09-10-2010, 05:56 PM #148
I used Gosen grip, pretty sure it's longer than AC402 (this Apacs is about G4 as well) ... normally I can go up much further (didn't stretch it so much at the end this time). Think I continued 50% overlap untill the end, normally when I reach the cone I no longer do 50%. Maybe you can try that if you also did 50% all the way ...
You can create the thick bottom any method, still no point wrapping it this way if you're not going to use the sticky end but I guess it's easy to use when you use your left-over bit without a sticky part at all .
Last edited by demolidor; 09-10-2010 at 05:59 PM.
09-20-2010, 03:17 AM #149
09-20-2010, 09:07 AM #150
10-02-2010, 05:28 AM #151
More pics of LCW's grip.. from the net.
10-02-2010, 05:31 AM #152
Here's mine.........1st time trying
10-03-2010, 12:40 PM #153
erm so for towel grips do u guys advice me to grip from the cone down or from the yonex sign up to the cone..
By eastcoast in forum GripReplies: 9: 11-04-2011, 12:21 PM
By Lindanftw in forum GripReplies: 2: 02-20-2011, 05:31 AM
By trowakage in forum GripReplies: 11: 09-17-2008, 12:50 AM
By joseph in forum GripReplies: 84: 11-22-2006, 04:11 PM