Results 18 to 34 of 36
Thread: Pre-weaving - what now?
03-12-2010, 04:35 PM #18
Preweaving really only saves time on frames with shared holes. Most good stringers can do a proper stringjob in about 45 mins or less even on frames with shared holes just by using a sharp cutter on the end of the string before passing through the shared hole. Just by angling the string in such a way to find a space to pass through. Most times one or two tries and you will be through. I string over a thousand frames per year and I don't bother with the preweaving anymore. Just my two cents.
03-12-2010, 08:38 PM #19
Preweaving is highly recommended for beginners in badminton stringing. this is not only confidence building, but also minimizing mistakes which will end up with frustration and lots of wasted strings after you pulled them tight.
as you are gaining experience, you will find out issues with preweaving, like mentioned in #17 post here. However, you can often find a way to avoid those issues.
after you become advanced level in stringing, you will find so many easiers ways to get stringing done.
03-12-2010, 08:52 PM #20
Here is a new pic I photoshopped. This is only what you need to do for the mains, it does not take into consideration the crosses. Crosses are easy though. If you guys want I can also make an image of that too. I just fine that there is a lot of confusion for how to do the mains towards the ends.
03-12-2010, 10:19 PM #21
Point well taken, Thanks
03-12-2010, 10:34 PM #22
i tried pre-weaving before and i have two issues with it:
1) it doesn't help the weaving process. in fact, it makes it even more difficult as the strings have almost no tension and goes everywhere.
2) tensioning the string always lead to the string twisting. seems to add more stress to the surface.
03-13-2010, 01:35 AM #23
03-14-2010, 08:07 PM #24
for starter, once you keep the strings kind of tight, and leave good starting loops in the middle and first cross (about 25cm long, and 2x for the center of main and 1x for the cross), you should be fine.
if twisting is a problem, simply do NOT pre-weave after #9/10 grommets.
03-15-2010, 05:57 AM #25
03-15-2010, 06:08 AM #26
03-15-2010, 07:38 AM #27
Who says pre-weaving cannot be done with adequate enough tension to make the weaving of the crosses easy?
You can actually pre-weave the mains first, hand-tension each main string by hand working from both the sides towards the center. Doing the mains is a two-step process, ending with reasonably tight mains, by pulling the two middle main strings with some rubber bands towards the handle and then just tighten them.
With reasonably tight mains you then pre-weave the crosses, which is an easy job.
After you have finished, just untie the rubber bands used to hold the mains tension.
To ensure fool-proof kink-free stringing, don't pre-weave the first 4 top cross strings.
03-15-2010, 08:32 AM #28
the professional stringer at All England 2010 :
- just 2 Yonex flying clamp
- Pre-weaving .....
03-15-2010, 10:27 AM #29
One piece string job or two piece?
03-15-2010, 12:06 PM #30
Kwun, weaving with out tension may be difficult for you but that doesnt mean its harder for everyone. It is a different feel that is learned.
Regarding twisting...Twisting occurs at the shared grommits because the tensioned string is pressing against the untensioned string while you pull it through. Some strings twist more or less than others. Since the twisting occurs when the loose string is pulled through, higher tension will cause more twisting. There is still some cases where you can pre string and it wont twist as much, and that depends on how the 2nd string (cross) goes through the shared grommit. I dont know if there is a technique to this, I just find it is random.
03-15-2010, 01:26 PM #31
twisting can be avoided during the pulling of mains. you just have to pay extra attention when you are pulling the mains through the grommets which the cross string is also there.
otherwise, pre-weaving or not is really a personal preference.
03-15-2010, 02:23 PM #32
03-15-2010, 02:24 PM #33
03-21-2010, 06:22 AM #34
Thankyou for that mains diagram , I have followed it , and it helped me so much!
Would it be possible to do one for the crosses aswell?
If anyone can help me on the tie-offs I would be very grateful!
Once again , thankyou for all the help!
By kwun in forum Badminton Stringing Techniques & ToolsReplies: 15: 01-10-2013, 05:06 PM
By Ouchee in forum Badminton Stringing Techniques & ToolsReplies: 4: 01-23-2012, 05:32 AM
By ToFuStew in forum Badminton Stringing Techniques & ToolsReplies: 2: 01-21-2011, 01:48 PM
By shlhu in forum Badminton Stringing Techniques & ToolsReplies: 2: 09-24-2010, 07:43 PM
By Sum in forum Badminton Rackets / EquipmentReplies: 1: 07-13-2001, 03:31 PM