Results 18 to 30 of 30
Thread: New Grommets
08-20-2010, 01:20 AM #18
Hi there guys. I have this problem. My Yonex AT900T shared grommets, specially at 5 o'clock and 7 o'clock positions (or maybe 4 and 8) are really stuck into their holes due to high tension. I have no grommet removal tool and it is not available in my country.
If any of you experienced this, how did you remove the shared grommets without using de-grommeting tool?
05-13-2011, 03:26 AM #19
Good news is,u can DIY,modify the new normal double string(large) grommet.First,u need a scissor.Cut it to the normal length of the original grommet.Then,u need a screwdriver,that can slightly fit in the grommet hole..Screw it,n use a blunt surfaced,for ex:the bottom handle of the screwdriver itself n make it flat.I've done this on most of my grommets replaced rackets.
05-13-2011, 03:51 AM #20
After u have it half way out,use ur nail cutter to clamp (don't cut them,otherwise u'll have a hard time to push them out) n pull the old grommets out.
Notice:U'll need a male nail cutter,not that mini nail cutter though..Otherwise u can't fit the space to clamp the big grommets.
Good luck on trying!
03-03-2012, 01:50 PM #21
sorry for reviving this thread but I have some things to ask
I'm about to get grommets from mbs (just buying two types and shorten them if needed) and a lot of you have been talking about type A and C, but I was wondering which are the MBS equivalents because the types available there are B,C,E,F,I
looking at the diameters, I assumed it would be type C and I but I just want to make sure
03-03-2012, 02:19 PM #22
On this subject, how tight should grommets be? I have the smallest ones from W&D (2.1mm iirc) and on yonex frames they are really hard to push in all the way, to the point that i sometimes have to shave a little bit off the grommet to get them to fit.
The last time i strung a YY frame i had to replace all of the single pass grommets, and after stringing they've pulled out a little, so that the flange isn't flush with the frame, so i'm going to have to restring and push them in more somehow.
03-03-2012, 08:51 PM #23
03-03-2012, 10:36 PM #24
03-06-2012, 03:01 PM #25
in other words, they are the right fit if:
- it is not so loose that it falls out on its own, and
- you can push it into the grommet hole with bare hands (without hurting yourself)
03-06-2012, 05:55 PM #26
Unless YY frames need smaller grommets than others, or this batch i have were made a little too big i'm at a loss.
03-06-2012, 06:02 PM #27
03-07-2012, 01:55 PM #28
I'm guessing that they are designed to squish down into themselves to make them more secure in the frame?
03-07-2012, 02:47 PM #29
yeah. it looks like it.
but it does look like Yonex's grommet are less than 2.1mm.
i have noticed that with recent Yonex rackets with single pass grommets hole, it does take some effort to insert the MBS grommets into the hole. i will measure the size of the MBS grommets when i get home tonight.
03-09-2012, 03:22 AM #30
i have two types of grommet that i got from MBS.
they measure 2.55mm and 2.09mm
By exxn0mercy in forum Badminton Rackets / EquipmentReplies: 3: 06-20-2009, 01:26 PM
By goldieandsilvie in forum Badminton Rackets / EquipmentReplies: 9: 03-17-2008, 11:07 PM
By markburry_90 in forum Market PlaceReplies: 1: 02-22-2006, 06:21 PM
By vienly in forum Market PlaceReplies: 4: 01-29-2005, 06:03 AM
By Marcel in forum Badminton Rackets / EquipmentReplies: 1: 03-30-2000, 11:16 AM