Results 1 to 12 of 12
04-08-2010, 03:10 AM #1
ARC-ZS and NS9900 stringing pattern
Hi all. I have a question about stringing patterns. My stringer does not seem to follow the Yonex recommended stringing instructions for the mentioned racquets. Here are some pics. I have hightlighted the location of the knots.
ARC Z Slash
Are these normal? If no, how much will it affect the racquet performance?
04-08-2010, 03:52 AM #2
Probably looked for HIS convenience to tie off and start mains. I don't think it will affect performance, but I guess it voids any guarantee u might hv, if u hv,
04-08-2010, 05:09 AM #3
that's very normal in Malaysia, most of the stringer didn't follow Yonex pattern.
04-13-2010, 12:26 PM #4
To my knowledge, it's "4 knots" style. The Yonex recommendation is 2 knots style as seen in your pic.
The 4 knots style is the way to cut the string into 2 parts, one for horizontal and another one for vertical.
04-13-2010, 12:43 PM #5
Yonex recommends 2 piece string, hence 4 knots, as they say 2 knots damage the frame. If you complain to them that you have a damaged frame with 2 knots, they are more strict than 4 knots going above the recommended tension.
As for the pattern from your photo's the knots on the bottom seem fine. As to the top crosses you need to see properly which route's he taken before the knot. Maybe he's done the top cross before the 2nd one which would mean it's closer to tie a knot where he has done rather than the stringing pattern on the 5th grommet. The closer the tie off, the more slack it cuts off in the tension.
04-13-2010, 02:16 PM #6
Its not just the tie off location that will make the string job good or not, but the overall quality of the string job/stringer. It could play well, it mite just be average. As I always say just play what feels good.
04-13-2010, 10:32 PM #7
the only problem with it is that the top cross tie off is moved lower
the stringer can just tie it off on the top main but i don't see why he would tie it off on a cross
i think its a bad place to tie off because there are now 3 strings going through that one hole. it will make more stress at that one spot
Last edited by Deathsticks; 04-13-2010 at 10:35 PM.
04-14-2010, 04:51 AM #8
@jedi: maybe you can show a picture of the side of the racket on the top knot side.
I have a hunch that the stringer has finished at cross 10, hence tying the knot at the corner grommet, as the smaller grommets you can only fit in one string.
In regards to performance, If the quality of stringing is good, the knots won't affect the performance of the racket.
04-14-2010, 10:44 AM #9
Thanks for all the insight guys. Ok, here's some snapshots of side of the Z Slash containing the top knot.
04-14-2010, 01:05 PM #10
Your stringers just messed around with the crosses but I don't know why, I guess it's just his preference or maybe his clamp fits better in that particular corner to cut off the slack. Ask him =). IMO it looks a bit messy but at the end of the day it's performance that counts. It doesn't change much if he has done a quality job. Anyway I took some photo's of one that I did which follows the pattern.
04-14-2010, 02:52 PM #11
It is fine. the only difference is the cross tie off at A5. There is common practice in Asian countires to fololw the pattern you just showed. It is not a big deal. It wont effect the performace whatsoever.
04-15-2010, 12:53 AM #12
Of course the stringing job is rather poor and also wrong.
The mains tie-offs should be at the two bottom grommets #8, not #6.
The starting cross knot should be at the top grommet #5, the bottom cross tie-off at the bottom grommet #6.
All his knots are at the wrong locations. In addition there are too many long strings unnecessarily skirting around the outside of the frame.
By TsAr83 in forum Badminton Stringing Techniques & ToolsReplies: 7: 04-22-2011, 02:40 PM
By noppy in forum Badminton Stringing Techniques & ToolsReplies: 4: 01-09-2010, 03:50 AM
By logi in forum Badminton Stringing Techniques & ToolsReplies: 7: 04-24-2008, 09:47 PM
By silentheart in forum Badminton Stringing Techniques & ToolsReplies: 8: 08-04-2006, 10:20 AM
By Vic in forum Badminton Stringing Techniques & ToolsReplies: 4: 11-16-2001, 09:53 AM