Results 1 to 17 of 19
11-18-2010, 07:25 PM #1
Fix a snapped Li Ning N90 in Melbourne Australia.
Recently My friend gave me his broken Li Ning N90 Woods edition racket, i was wondering if it could be fixed within melbourne, australia. the racket is generally fine, except that the head has been snapped on one side, please help me. I know the racket will never be the same, and plan to string it at 20lbs if it can be fixed.
Thanks so much,
11-19-2010, 01:01 AM #2
As you can see, only half of the head has snapped, otherwise the racket is in decent condition.
11-20-2010, 03:02 AM #3
Help please guys
11-20-2010, 03:16 AM #4
forget it. it is a goner. a fixed racket will never be anywhere near as strong as a intact one.
11-20-2010, 01:03 PM #5
How did it snapped?
11-20-2010, 08:31 PM #6
11-20-2010, 10:30 PM #7
11-23-2010, 03:41 AM #8
I don't think you're getting it... I want to have it fixed, this isn't how im going to play with it... it would just be nice if someone would tell me WHERE i could go to fix it
11-24-2010, 12:39 AM #9
please help me
11-24-2010, 12:51 AM #10
As others have said just forget it. You even superglue it
11-24-2010, 01:16 AM #11
i would just like to have it fixed and strung at like 20 lbs
I can fix the racket-head for you. But it's only for looks. You will not be able to get it strung anything higher than 10 lbs.
A cracked racket-head is like a cracked egg-shell; our BCers have been trying to tell you this (if you have not understood it).
Last edited by chris-ccc; 11-24-2010 at 01:20 AM.
12-07-2010, 04:38 AM #12
Thanks Chris-ccc I completely understand that a cracked racket will never be the same, but I just want the racket fixed. thanks
12-07-2010, 05:22 AM #13
12-07-2010, 05:35 AM #14
12-07-2010, 05:56 AM #15
12-07-2010, 08:19 AM #16
1. Carefully remove paint to access graphite 1.5-2 cm to the both sides of the crack.
2. Get glass-fiber cloth - 150 or 300 gr/m2 thickness is ok. Used in car/boat repairs.
3. Get an epoxy glue/resin with high hardness (a very small amout is needed)
4. Cut a tape of glass-fiber cloth 3 to 4 cm wide and up to 10 cm in length. Scissors will be blunted after this. Protect your hands with gloves.
5. Mix an epoxy
6. Apply epoxy to the racket and to the cloth
7. Wrap cloth tape aroud the racket 2 times
8. FIx it with a piece of thread/yarn - wrap it many times around.
9. Clean all the mess around
10. Allow to dry for 24 hours. Consider heating it slightly if weather is humid. Make sure that the parts are aligned propely.
11. Remove unneded epoxy and sharp edges with a file
12. Drill a holes for a string
13. Install grommets - the longer ones will be needed. You can try to use tubing instead of grommets as well.
14. Tension it to 10-11 kg
15. Test you new very head heavy racket
12-07-2010, 01:04 PM #17
the final result
The final result must be like shown on picture.
The two AT700 cracked due to hitting the floor.
By Easy Tiger in forum Market PlaceReplies: 38: 09-26-2011, 07:28 PM
By Talkingtaco2 in forum Badminton Rackets / EquipmentReplies: 5: 10-23-2010, 04:48 AM
By GRObFURSt in forum Australia / New ZealandReplies: 67: 12-23-2009, 12:14 PM
By cintamami in forum Market PlaceReplies: 10: 03-20-2005, 07:47 PM
By jeetz_2 in forum Australia / New ZealandReplies: 9: 06-24-2002, 10:23 PM