Results 1 to 15 of 15
Thread: Victor machine c-7031
02-07-2011, 07:48 AM #1
Victor machine c-7031
Doest anyone string with a VICTOR C-7031. if so please let me know. i am struggling to know the way to get around the machine and how to mount the racket. as im not sure im doing it right since the racket is turning out a bit egg shaped, especially near the end of the bottom of the racket. even with low tension such as 22lbs.
Please guide me you MASTER stringers out there!!!
02-07-2011, 10:42 AM #2
Nice looking machine, looks like a Eagnas Combo 8010 base. Are the 6/12 o'clock post hold down or floating?
02-07-2011, 09:01 PM #3
the 6/12 oclock post are hold down i think. because when i put the racket in, on top of the racket there is a silver looking thing to place on top. then i need to lock it in. the first picture on the top right shows what i mean if u dont understand my english haha. hope you can help me out!
02-07-2011, 09:12 PM #4
You may need to pull the towers back or away from each other, so the racket frame fits snuggly, but not so much it's actually pulling on the frame. Also try to center the frame as much as possible, with the center crosses in the center of the turntable. This will help minimize frame distortion when you are pulling tension.
02-08-2011, 07:39 AM #5
I see..should the towers be even on each side?
sorry I don't seem to understand by what u mean centre the frame as much as possible...because when I mount the racket shouldn't it already be centered?!
02-08-2011, 07:50 AM #6
02-09-2011, 07:40 AM #7
i have done everything you have said JOHNLOWE88 and COVINASTRINGER...and yes from a round racket to much better shape. still a little bit egg shape though. but hey im not too sure how thin the racket is supose to be. anyone got any pictures? still need to make it a big longer...
ALSO...i know this a stupid Q, but just to make sure. when stringing at a high tension such as 28lbs, of course the racket will go round a bit right? or should it still stay in its shape? thanks though for putting time into writing to my post. much appreciated! im starting to like posting! hopefully when i get good at stringing and keeping its shape i can help others. =]
02-09-2011, 09:38 AM #8
Ok. Usually the way to test how bad it is, is when the racquet head is not strung, trace the outline - inside and outside on a piece of paper, then after stringing it, place it on the paper and see where it is different. I am told that a change in length of a couple of mm should be no issue. Certainly I don't generally string at this high tension, and my racquets don't appear to change much at all.
A question though, after stringing - before you remove it from the clamps, does it appear to be rounded? The side supports are supposed to help the racquet head keep its shape. When you loosen the side supports - do they appear to be pressing a lot harder than before stringing? You can normally feel from the winding knob if it is under a lot of tension. Does the racquet head look rounder now before removing the top and throat supports? If it seems to squash down when removing the top and throat support - that would suggest that the mains tension is higher than the crosses. You do know that the mains strings are those that go from top to throat (or t joint), i.e. in line with the handle - and the crosses are right angles to the handle - right?
Also, you don't appear to mention what the racquet is - what is it? Take a photo of the racquet head for us to look at - this would help. Also show us how you mount the racquet on the stringing machine.
To answer your question about stringing at high tension, a lot of people here on the forum do string at 28lbs and don't have an issue with the racquet head changing shape very much at all.
By the way, my name is John, and I live in Dundas, a suburb of Sydney.
02-09-2011, 09:46 AM #9
Hi - I see you have another thread talking about this also. Your racquet is a Armortec 900 - I think you said that you are stringing the crosses top down, but Yonex recommends going from throat up. Maybe you should try stringing it according to Yonex instructions first, so that you get used to stringing first before you change. See this link...
P.S. You do have a genuine Yonex - right?
Last edited by johnlowe88; 02-09-2011 at 09:47 AM. Reason: add P.S.
02-09-2011, 08:36 PM #10
02-09-2011, 09:31 PM #11
Ok - just wanted to check.
02-23-2011, 09:29 AM #12
Just wonder where did you buy this machine and how much is it ? Is it a good reliable machine ? I am thinking of getting one in future.
02-23-2011, 10:39 PM #13
Related Machine: C-7030
johnlowe88 is correct about centering the middle cross to the center of the turntable and the feel of the bottom shoulder suppports pressing hard against the knobs. Unfortunately, C-7030 has one column permanently fixed to the turntable. Therefore, it is not possible to center the frame as suggested. As a result, one has to lengthen the frame by quite a bit in order for the frame not to come out short and rounded.
02-23-2011, 10:54 PM #14
02-27-2011, 10:18 PM #15
Yes John, the OP mentioned the C-7031 but I briefly diverted our attention to the C-7030.
By BengGuan in forum Badminton Stringing Techniques & ToolsReplies: 41: 02-27-2012, 12:25 AM
By limak in forum Badminton Rackets / EquipmentReplies: 3: 08-03-2011, 04:19 PM
By bbi2004 in forum Badminton Stringing Techniques & ToolsReplies: 8: 02-18-2011, 10:42 AM
By Pete LSD in forum Market PlaceReplies: 3: 02-20-2008, 09:29 AM